Zimmer® IMPRESSION COPINGS

Tapered Screw-Vent® (TSV), Screw-Vent®

Fig. 1

Implants are pre packaged with a multi purpose fixture mount (Fig.1), this fixture mount may be utilized as a indirect impression coping. The fixture mount/impression copings are fabricated with a emergence profile 1mm larger than the platform diameter of the implant.

Indirect engaging, fixture level impression copings (Fig.2) for the indirect impression technique are color coded in compliance with the color coding scheme of Screw-Vent® implants. Green signals the 3.5mm platform and purple indicates the 4.5mm platform diameter while yellow corresponds to the 5.7mm platform.

Fig. 2

Impression copings consists of a symmetrically machined impression coping body and separate screw. The screw should be flush with the impression coping body once fully seated on to the implant. Each platform group impression coping is machined in several emergence profiles with the exception of 5.7mm platform impression copings. 3.5mm platform impression copings are available with emergence profiles of 3.5 (catalog # HLT3/3), 4.5 (catalog # HLT3/4) and 5.5mm (catalog # HLT3/5) while 4.5mm platform impression copings are produced with emergence profiles of 4.5 (catalog # HLT4/4), 5.5 (catalog # HLT4/5) and 6.5mm (catalog # HLT4/6). The 5.7mm platform impression coping is produced in a single emergence profile of 6mm (catalog # HLT5/6).

Direct engaging, fixture level impression copings (Fig.3) for the direct impression technique are color coded in compliance with the color coding scheme of Screw-Vent® implants. Green signals the 3.5mm platform and purple indicates the 4.5mm platform diameter while no direct impression copings are available for 5.7mm platform implants.

Fig. 3

Impression copings consists of a symmetrically machined impression coping body and separate screw. The screw extends past the impression coping body once fully seated on to the implant. Each platform group impression coping is machined in several emergence profiles. 3.5mm platform impression copings are available with emergence profiles of 3.5 (catalog # DHT3/3), 4.5 (catalog # DHT3/4) and 5.5mm (catalog # DHT3/5) while 4.5mm platform impression copings are produced with emergence profiles of 4.5 (catalog # DHT4/4), 5.5 (catalog # DHT4/5) and 6.5mm (catalog # DHT4/6).

Fig. 4

Abutment level impressions for already installed titanium Hex-Lock® abutments are carried out with color coded plastic impression copings (Fig.4). The color coding of the plastic impression copings does not comply with the general platform color coding of the Screw-Vent® implant system but is designed to indicate the emergence profile of the installed Hex-Lock® abutment. Blue represents a 3.5mm emergence and orange signals a 4.5mm emergence profile while red designates a 5.5mm emergence profile impression coping. Yellow represents the largest emergence profile of 6.5mm. All four emergence profile impression copings are produced for straight (catalog # ZOCIMP3S, ZOCIMP4S, ZOCIMP5S, ZOCIMP6S) and angled (catalog # ZOCIMP3A, ZOCIMP4A, ZOCIMP5A, ZOCIMP6A) abutments separately. Complete kits including the impression coping, analog, temporary coping and burnout coping are also sold (straight catalog # ZORKIT3S, ZORKIT4S, ZORKIT5S, ZORKIT6S and angled catalog # ZORKIT3A, ZORKIT4A, ZORKIT5A, ZORKIT6A).

Fig. 5

Abutment level impressions for already installed short titanium Hex-Lock® abutments are carried out with color coded plastic impression copings (Fig.5). The short titanium Hex-Lock® abutment impression copings are not compatible with regular Hex-Lock® titanium abutment impression copings. Color coding of the plastic impression copings does not comply with the general platform color coding of the Screw-Vent® implant system but is designed to indicate the emergence profile of the installed short Hex-Lock® abutment. Orange signals a 4.5mm emergence profile while red designates a 5.5mm emergence profile and yellow indicates the largest emergence profile of 6.5mm. Impression copings are offered as a kit, including the color coded plastic impression coping, plastic analog, temporary and waxing coping. (catalog # SAKIT4, SAKIT5, SAKIT6)

Zimmer® One-Piece

Fig. 6

Abutment level impressions for One-Piece implants are carried out with color coded plastic impression copings (Fig.6). The color coding of the plastic impression copings does not comply with the general platform color coding of the Screw-Vent® implant system but is designed to indicate the emergence profile of the abutment portion of the One-Piece implant. Blue represents a 3.5mm emergence and orange signals a 4.5mm emergence profile while red designates a 5.5mm emergence profile impression coping. All three emergence profile impression copings are produced for straight (catalog # ZOCIMP3S, ZOCIMP4S, ZOCIMP5S) and angled (catalog # ZOCIMP3A, ZOCIMP4A, ZOCIMP5A) abutments separately. Complete kits including the impression coping, analog, temporary coping and burnout coping are also sold (straight catalog # ZORKIT3S, ZORKIT4S, ZORKIT5S and angled catalog # ZORKIT3A, ZORKIT4A, ZORKIT5A).

AdVent®

Dedicated AdVent® fixture level impression copings are only available for 4.5mm platform implants. 5.7mm platform implants are impressed with impression copings from the Screw-Vent® 5.7mm platform product group. The 4.5mm platform impression coping (catalog # AVIT/4) may be utilized for the indirect and direct impression technique. Direct impressions are carried out by exchanging the included fixation screw of the AVIT/4 impression coping with a longer fixation screw (catalog # DHTS). A multi purpose abutment (catalog # FMA4) intended as a fixture mount, impression coping and temporary abutment may be used as an alternative indirect impression coping. 5.7mm platform implants can only be impressed with the indirect impression technique, use catalog # HLT5/6 or the multi purpose abutment FMA5.

Tapered SwissPlus®, SwissPlus®

Indirect engaging, fixture level impression copings for the indirect impression technique are not color coded for platform diameter identification purposes. 3.8mm platform diameter, internal hexagon impression copings as a single version 4.6mm emergence profile abutment (catalog # SPMT). The fixture mount (catalog # FMSM) included with each 3.8mm platform implant can also be utilized as a indirect impression coping. 4.8mm platform internal octagon, indirect impression copings are available in two emergence profiles of 5.2mm (catalog # OPT/5) and 6mm (catalog # OPT/6). The fixture mount included with each 4.8mm platform diameter implant may also be utilized as a indirect impression coping.

Direct impression copings for the direct impression taking technique are not offered for the SwissPlus® implant system.

Abutment level impression copings for the abutment level impression technique are available as a multi purpose (impression coping/burn out coping) plastic coping. 3.8mm platform abutment level impression copings (catalog # SPMC) work in conjunction with the already installed narrow straight abutment SPMA2 while 4.8mm platform diameter abutment level impressions are carried out with the OPC impression coping.

Spline

Not covered

ERA Mini

Not covered